BKT Elektronik ACBS Installation And Configuration Manual Download Page 70

Page: 70 / 92

www.bkte.pl

BKT ACBS - installation and configuration manual of the access control system with RS485 bus interface

Similar actions should be performed for the line IN3-door handle
sensor:



Select input C1_100_IN3



Click Edit



Tick Multifunction option



Click OK



Now you can use again the IN3-door handle sensor input for
configuration.

The configuration process of the automation node that will be
responsible for the LED1 control:



In the system tree, right-click on System->Networks->
->DataCenter (configurable name)> C1 (configurable controller
name)> Automation Nodes and select Open

A new automation node should be created that will be responsible
for controlling the LED:



Click Add

Summary of Contents for ACBS





























































































Search results

Summary of Contents for ACBS

Reviews:

Related manuals for ACBS

Brands by name

Popular brands

BKT Elektronik ACBS, Installation And Configuration Manual

Search results

Summary of Contents for ACBS

Reviews:

Related manuals for ACBS

Brands by name

Popular brands