Biosan Labaqua Operating Manual Download Page 4

1.  Safety precautions 

The following symbol means: 

 

Caution!

 

Make sure you have fully read and understood the present  Manual 
before using the equipment. Please pay special attention to sections 
marked by this symbol. 

 

Caution!

 

Do  not  service  the  unit  while  the  open  UV  lamp  is  switched  ON. 
Otherwise  it  can  expose  the  operator  to  a  dangerous  level  of  UV 
emission. 

GENERAL SAFETY 

 

Use only as specified in the operating manual provided. 

 

The unit should not be used if dropped or damaged. 

 

The  unit  must  be  stored  and  transported  in  a  horizontal  position  (see  package 
label). 

 

After transportation or storage, keep the unit at room temperature for 2-3 hrs before 
connecting it to the electric circuit. 

 

Use  only  cleaning  and  decontamination  methods  recommended  by  the 
manufacturer. 

 

Use only original accessories (fuses, tubes, etc.) provided by the manufacturer and 
ordered specifically for this model. 

 

Do not make modifications to the design of the unit. 

 

Do not block any ventilation openings. 

 

Do not operate the unit with its covers removed. 

 

Do not drink deionized water. 

WATER LEAKAGE SAFETY 

 

Make sure that all water connection tubes are unbent, kink-free. 

 

Make sure that all water connectors are tight. 

 

When installing the tank, connect the fitting marked „Overflow” to the drain. Make 
sure  that  the 

drain level is lower than the „Overflow” fitting level. This will prevent 

water leakage in case of tank level sensor failure. 

 

Do not operate the tank pump if there is no water in the tank. Tank pump may fail if 
it is run dry. 

 

A  5 

μm sediment filter has to be installed in the feed water supply line. Failure to 

install  the  filter  may  result in clogging  of  strainer  inside  the  system  and  water  flow 
blockage. 

 

Shut off tap water supply when leaving the system unattended. 

ELECTRICAL SAFETY 

 

A  power  line  regulator  may  be  required  in  the  areas  where  the  supplied  power  is 
subject to voltage fluctuations exceeding 10% of the nominal. 

 

Connect  only  to  a  mains  outlet  with  voltage  corresponding  to  that  on  the  serial 
number label. 

 

Verify that the fuses are properly installed. 

Summary of Contents for Labaqua





















Reviews: