biodex 950-440 Instructions For Use Manual Download Page 14 | Manualshive

Page: 14 / 76

biodex 950-440 Instructions For Use Manual Download Page 14

14

6.

Insert finishing washer over the stud.

NOTE:

The flange should be sticking up.

7.

Apply Loctite to second nut.

8.

Thread on the second nut and tighten.

NOTE:

Ensure the hooks are orientated correctly, pointing outwards as shown in the

diagram before tightening.

9.

Apply plastic cap.

10.

Repeat steps 1-9 for the remaining three hooks.

Turning On the System

The Balance System SD turns on when the power cord is plugged into an AC power supply. The
software starts automatically.

1.

Plug the power cord of the Balance System SD into an AC power supply. The Home screen is
displayed (see Figure 2.1). The Balance System platform is active and in the locked position.

Figure 2.1.

Home Screen .

2.

Turn on the printer.

3.

If an external monitor is used, turn on the monitor. At the Home screen, select <Utilities >
<Configuration >, <System Configuration >, <Screen Configuration >, and <Mirror to
External Monitor>.

«
...
12
13
14
15
16
...
»

Summary of Contents for 950-440













































































Reviews:

No comments