Billion BiPAC 9800N User Manual Download Page 11

Page: 11 / 111

Device Description

The Front LEDs

LED

Meaning

Internet

Lit orange when WAN port fails to get IP address.
Lit green when WAN port gets IP address successfully.
Lit off when the device is in bridge mode or when WAN connection

absent.

WAN

Lit green when the device is connected to a broadband connection

device.
Blinking when data is transmitted/received.

WPS

(BiPAC 9800N

only)

Flash green when WPS configuration is in progress. However, if

WPS fails, the LED will only lit for 1 min before goes off.

Wireless

(BiPAC 9800N

only)

Lit green when a wireless connection is established.
Flash green when data is transmitted/received.

Ethernet port

1X — 4X

(RJ-45 connector)

Lit orange when one of LAN ports is connected to an Ethernet

device.
Lit green when the speed of transmission hits 1000Mbps; Lit orange

when the speed of transmission hits 10/100Mbps.
Blinking when data is transmitted/received.

Power

When the device is booting, the green light will lit while the orange

light will flash.
When the system is ready, it will lit green.
Lit orange when the device fails to boot or when the device is in

emergency mode.

Summary of Contents for BiPAC 9800N
















































































































Search results

Summary of Contents for BiPAC 9800N

Reviews:

Related manuals for BiPAC 9800N

Brands by name

Popular brands

Billion BiPAC 9800N, User Manual

Search results

Summary of Contents for BiPAC 9800N

Reviews:

Related manuals for BiPAC 9800N

Brands by name

Popular brands