Billion BiPAC 9800N User Manual Download Page 37

Page: 37 / 111

WAN Connect Mode

PPPoE connection

Username:

Enter the username provided by your ISP. You can input up to 256 alphanumeric

characters (case sensitive).

Password:

Enter the password provided by your ISP. You can input up to 32 alphanumeric

characters (case sensitive).

Service Name:

This item is for identification purposes. If it is required, your ISP will provide you

the necessary information. Maximum input is 32 alphanumeric characters.

IP Address:

Enter your fixed IP address.

Authentication Protocol:

Default is Auto. Please consult your ISP on whether to use PAP, CHAP

or MSCHAP.

MTU:

Maximum Transmission Unit. The size of the largest datagram (excluding media-specific

headers) that IP will attempt to send through the interface.

Summary of Contents for BiPAC 9800N
















































































































Search results

Summary of Contents for BiPAC 9800N

Reviews:

Related manuals for BiPAC 9800N

Brands by name

Popular brands

Billion BiPAC 9800N, User Manual

Search results

Summary of Contents for BiPAC 9800N

Reviews:

Related manuals for BiPAC 9800N

Brands by name

Popular brands