Billion BiPAC 9800N User Manual Download Page 8

Page: 8 / 111

Hardware Specifications

Physical Interface

Please refer to the instructions on the label of the outer box to get the specification of your device.

• Optical SC-connector with options:

- 100BASE-LX dual fiber single-mode WAN (Tx/Rx1310nm)

- 100BASE-BX single-strand single-mode WAN (Tx1310nm/Rx1550nm)

- 100BASE-FX dual fiber multimode WAN (Tx/Rx1310nm)

- 1000BASE-LX dual fiber single-mode WAN (Tx/Rx1310nm)

- 1000BASE-BX single-strand single-mode WAN (Tx1310nm/Rx1490nm)

• 100/1000BASE Optical SFP Optical convector

• WLAN: 3 x detachable antennae (BiPAC 9800N only)

• Ethernet: 4-port 10/100/1000M auto-crossover (MDI / MDI-X) Switch

• Factory default reset button

• WPS push button (BiPAC 9800N only)

• Power jack

• Power switch

Operating Environment

Operating temperature: 0 – 40°C

Storage temperature: -20 – 70°C

Humidity: 20 – 95% non-condensing

Summary of Contents for BiPAC 9800N
















































































































Search results

Summary of Contents for BiPAC 9800N

Reviews:

Related manuals for BiPAC 9800N

Brands by name

Popular brands

Billion BiPAC 9800N, User Manual

Search results

Summary of Contents for BiPAC 9800N

Reviews:

Related manuals for BiPAC 9800N

Brands by name

Popular brands