BETTCHER INDUSTRIES Whizard Quantum Series Operating Instructions & Parts List Manual Download Page 67

Page: 67 / 134

Maintenance

Manual No. 101300

Maintenance

5-25

March 16, 2015

Operating Instructions and Parts List for the Whizard Quantum

Trimmer

OPTIONAL DISC GAUGE OR DEPTH GAUGE INSTALLATION AND
ADJUSTMENT (CONTINUED)

Adjustable Depth Gauge for Models Q880 (B&S), Q1880, Q1400
and Q1500 Only

These tools come equipped with an adjustable
depth gauge for setting a controlled product trim
thickness. The depth gauge can be adjusted for cuts
up to ¼” thick.

A depth gauge setting device is also

available.

•

Slide the depth gauge downward along the
cover plate grooves until the depth gauge
clamps catch in position.

•

The final height adjustment can be made after
the blade is installed.

•

Tighten the two attachment screws.

Adjustment

•

Hold the handpiece with the blade facing
downward.

•

Loosen the attachment screws at the base of the plastic depth gauge.

•

Adjust the gauge setting by sliding it up or down to the desired height.

•

Retighten the attachment screws.

ATTACHMENT
SCREWS

COMPANY

CONFIDENTIAL

Summary of Contents for Whizard Quantum Series







































































































































Search results

Summary of Contents for Whizard Quantum Series

Reviews:

Related manuals for Whizard Quantum Series

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard Quantum Series, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard Quantum Series

Reviews:

Related manuals for Whizard Quantum Series

Brands by name

Popular brands