manualshive.com logo in svg

BETTCHER INDUSTRIES Whizard Quantum Series, Operating Instructions & Parts List Manual, Page: 66 / 134

Share
Download
BETTCHER INDUSTRIES Whizard Quantum Series Operating Instructions & Parts List Manual Download Page 66

Maintenance

5-24

Maintenance

Manual No. 101300

Operating Instructions and Parts List for the Whizard

 

Quantum

®

 Trimmer

March 16, 2015

OPTIONAL DISC GAUGE OR DEPTH GAUGE INSTALLATION AND 
ADJUSTMENT

Optional Disc Gauges for 
Models Q850, Q1850, Q1000 
and Q1300

Optional adjustable disc gauges are available 
for the Q850, Q1850, Q1000 and Q1300 
trimmers. 

Refer to Section 7, Service Parts to 

order.

•

Slide the disc gauge downward along the 
cover plate grooves until the disc gauge 
clamps catch in position.

•

The final height adjustment can be made 
after the blade is installed.

•

Tighten the two attachment screws.

Adjustment

•

Hold the handpiece with the blade facing 
downward.

•

Turn the adjustment knob clockwise for a thicker cut, or counterclockwise for a thinner cut.

NOTE:

 Take care not to turn too far as the depth control hub may disengage from the shaft.

ATTACHMENT

SCREWS (2)

ADJUSTMENT KNOB

DEPTH / DISC GAUGE

COMPANY 

CONFIDENTIAL

Summary of Contents for Whizard Quantum Series







































































































































Reviews:

No comments