BETTCHER INDUSTRIES Whizard Quantum Series Operating Instructions & Parts List Manual Download Page 54

Page: 54 / 134

Maintenance

5-12

Maintenance

Manual No. 101300

Operating Instructions and Parts List for the Whizard

Quantum

Trimmer

November 13, 2018

DAILY INSPECTIONS & MAINTENANCE (CONTINUED)

Whizard Quantum

Driveline Replacement

•

When the driveline needs to be replaced, the driver assembly may be retained and reused.

•

Hold the driveline (#1) in a vise.

•

Unscrew the driver assembly (#4) by turning counterclockwise using the wrench flats on the

drive end assembly.

•

Remove the nylon washer (#3), casing latch collar (#2) or lever mounting collar (#5) from

the casing.

•

Discard the driveline but retain and reuse the driver assembly (#4), the nylon washer (#3),

the casing latch collar (#2) - or the lever mounting collar (#5) and disconnect lever (#6).

To Reassemble the Drive End Assembly to a new Whizard
Quantum

Driveline

•

If using the driveline disconnect, place the disconnect lever (#6) onto the lever mounting

collar (#5).

•

Slip the driveline latch collar (#2) or lever mounting collar (#5) with disconnect lever (#6)

onto the new driveline.

•

Slip the nylon washer (#3) onto the new driveline.

•

Clean the threads of the new driveline assembly and apply 2-4 drops of Loctite #222

hread

locker or equivalent.

•

Screw the driver assembly (#4) on the new driveline.

•

Tighten by hand and then with a wrench while holding the driveline by hand.

NOTICE

NOT

hold the new driveline in a vise or use pliers as damage will occur. It is not necessary

to over-tighten this joint.

COMPANY

CONFIDENTIAL

Summary of Contents for Whizard Quantum Series







































































































































Search results

Summary of Contents for Whizard Quantum Series

Reviews:

Related manuals for Whizard Quantum Series

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard Quantum Series, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard Quantum Series

Reviews:

Related manuals for Whizard Quantum Series

Brands by name

Popular brands