BETTCHER INDUSTRIES Whizard Quantum Series Operating Instructions & Parts List Manual Download Page 71

Page: 71 / 134

Maintenance

Manual No. 101300

Maintenance

5-29

March 16, 2015

Operating Instructions and Parts List for the Whizard Quantum

Trimmer

FAULT DETECTION AND CORRECTION (CONTINUED)

PROBLEM

PROBABLE CAUSE

REMEDY

Dull Blade

Improperly sharpened
blades will cause loss of
production, increase
wear of parts, and opera-
tor fatigue.

Sharpening can best be accom-
plished by use of a Whizard

Model 210 Universal Blade
Sharpener, or Bettcher

AutoEdge. Blades can also be
sharpened by hand.

Blade not steeled prop-
erly.

Refer to Section 4, Steeling the
Blade.

Optional Thumb

Support

Anti-rotation splines
have worn.

Replace.

Spring Lost from

Driveline

Improper assembly.

Refer to Section 5, Driver
Assembly Inspection and
Replacement.

Blade Skips or Will Not

Rotate

Handpiece bearing worn.

Check / Replace Bearing.

Casing not fully engaged
or inserted.

Make certain the casing is fully
inserted to the drive position.

Broken flexshaft in the
Whizard Quantum

Driveline.

Replace Whizard Quantum

Driveline.

COMPANY

CONFIDENTIAL

Summary of Contents for Whizard Quantum Series







































































































































Search results

Summary of Contents for Whizard Quantum Series

Reviews:

Related manuals for Whizard Quantum Series

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard Quantum Series, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard Quantum Series

Reviews:

Related manuals for Whizard Quantum Series

Brands by name

Popular brands