BETTCHER INDUSTRIES Whizard Quantum Series Operating Instructions & Parts List Manual Download Page 53

Page: 53 / 134

Maintenance

Manual No. 101300

Maintenance

5-11

November 13, 2018

Operating Instructions and Parts List for the Whizard Quantum

Trimmer

DAILY INSPECTIONS & MAINTENANCE (CONTINUED)

Whizard Quantum

Driveline

•

The Whizard Quantum

Driveline includes

a casing and flexible shaft that is factory

lubricated and does not require ongoing

maintenance lubrication.

•

NOTE:

The flexible shaft is not removable

from the casing.

•

Inspect the casing for any cracks, tears or

other wear. If any damage is found, replace

the Whizard Quantum

Driveline.

•

Check to ensure that the flexshaft driver can

freely rotate in the casing. If it will not

rotate, replace the entire assembly.

FLEXSHAFT DRIVER

COMPANY

CONFIDENTIAL

Summary of Contents for Whizard Quantum Series







































































































































Search results

Summary of Contents for Whizard Quantum Series

Reviews:

Related manuals for Whizard Quantum Series

Brands by name

Popular brands

BETTCHER INDUSTRIES Whizard Quantum Series, Operating Instructions & Parts List Manual

Search results

Summary of Contents for Whizard Quantum Series

Reviews:

Related manuals for Whizard Quantum Series

Brands by name

Popular brands