9
Repair
Check pool for any leaks from valves or seams, check the ground cloth
for any evident water loss. Do not add chemicals until this has been
done.
Dismantling
1. Unscrew the drain valve cap on the outside of the pool counter
clockwise and remove.
2. Connect the adaptor to the hose and put the other end of the hose in
the area where you are going to drain your pool. (Check local
regulations for drainage by-laws).
3. Screw the control ring of the hose adaptor clockwise onto the drain
valve. The drain valve will be open and water will start to drain
automatically.
ATTENTION:
Water flow can be controlled with the control ring.
4. When draining is finished, unscrew the control ring to close the valve.
5. Disconnect the hose.
6. Screw the cap back onto the drain valve.
7. Air dry pool.
ATTENTION:
Do not leave the drained pool outside.
Storage and Winterization
1. Please remove all the accessories and spare parts of the pool and store them clean and dry.
2. Once pool is completely dry, sprinkle with talcum powder to prevent pool from sticking together, fold pool carefully. If pool is not completely dry,
mold may result and will damage the pool liner.
3. Store liner and accessories in a dry place with a moderate temperature between 5ºC / 41ºF and 38ºC / 100ºF.
4. During the rainy season, pool and accessories should be stored as per above instructions also.
5. Improper draining of the pool might cause serious personal injury and/or damage to personal property.
6. We strongly recommend the pool is disassembled during the off season (winter months). Store in a dry location out of children’s reach.
Jet Nozzle Maintenance
1. Twist untill hearing a “click” sound, and pull out the Jet Nozzle to clean the debris.
2. Insert and twist clockwise to put it back.
Replace if necessary.
7. If it rains, check that the water level is not higher than the specified
level. If water exceeds the specified levels, drain the pool to the
specified level.
8. Do not use the pump when the pool is in use.
9. Cover the pool when not in use.
10. For pool water treatment, the pH value is very important.
ATTENTION:
Do not leave the drained pool outside.
The following parameters ensure good quality water
Parameters
Water clarity
Colour of the water
Turbidity in FNU/NTU
Nitrate concentration above that of fill water in mg/l
Total organic carbon (TOC) in mg/l
Redox potential against Ag/AgCI 3,5 m KCl in mV
pH value
Free active chlorine (without cyanuric acid) in mg/l
Free chlorine used in combination with cyanuric acid in mg/l
Cyanuric acid in mg/l
Combined chlorine in mg/l
Values
clear view of the pool bottom
no colour should be observed
max. 1,5 (preferably less than 0,5)
max. 20
max. 4,0
min. 650
6,8 to 7,6
0,3 to 1,5
1,0 to 3,0
max 100
max 0,5 (preferably close to 0,0 mg/l)
- Jatkuva, aktiivinen ja tarkkaavainen heikkojen uimareiden tai
- Jotta lapsia estettäisiin hukkumasta, suosittelemme sulkemaan
pääsyn altaalle suojalaitteella. Jotta lapsia estettäisiin kiipeämästä
- Jos suodatinpumppu asennetaan, noudata pumpun ohjekirjan
- Jos tikkaat asennetaan, noudata tikkaiden ohjekirjan ohjeita.
Jos sinulla on suodatinpumppu, lue pumpun käyttöohjeet.
Jos et noudata tässä annettuja kunnossapito-ohjeita,
7. Jos sataa, tarkista, ettei veden pinta ole korkeammalla kuin
ohjeiden mukaisella tasolla. Jos veden pinta ylittää ohjeiden
