background image

51440, 51443

4

Rev. C   0301

Windshield Retainer - Left,
Qty - 1, PN 225.43

Because of Generic Packaging, extra parts may be included.

Parts List and Hardware Identification

Check off each item

Windshield Retainer - Right,
Qty - 1, PN 225.42

Top Fabric

Qty - 1

Door - Right

Qty - 1   51443 Only

Door - Left

Qty - 1   51443 Only

Adhesive PSA
       Hook Strip

Qty - 8"

Buckle Strap

Qty - 2

Bow Assembly - Right,
Qty - 1, PN 244.52

Bow Assembly - Left,
Qty - 1, PN 244.53

#10-32 Hex Nut,
Qty - 24, PN 151.82

Threaded Body Stud,
Qty - 24, PN 151.81

#10-24 Locknut,
51443 Only
Qty - 8, PN 195.93

Wing Nut, Qty - 2,
PN 151.83

5/16 x 3/4" Hex Bolt,
Qty - 2, PN 116.03

#10 x 1/2" Oval Head
Phillips Screw, Qty - 4,
PN 155.49

#8 x 1/2" Pan Head
Washer Screw - Black,
Qty - 9, PN 200.48

#14 Sheet Metal Screw,
Qty - 4, PN 243.51

#10-24 x 3/8" Truss Head
Machine Screw - Black,
51443 Only,
Qty - 8, PN 195.92

Paddle Handle - Door
51443 Only
Qty - 2, PN 245.46

Footman Loop, Qty - 2,
PN 272.29

Bow Coupler, Qty - 2,
PN 244.73

Door Striker
51443 Only
Qty - 2, PN 256.30

Horizontal Rod Bracket,
Qty - 2, PN 13.85

#10 x 1/2" S/M Screw,
Qty - 4, PN 1.92

Summary of Contents for 51440














Reviews: