Bestok 8210A User Manual Download Page 8

- 7 -

again until the cover clicks audibly into place.

To increase the operating time, you can use an additional 4 x 1.5 V
batteries in the battery compartment of the addtional battery box.

To do this, carefully push the lock on the battery compartment cover upwards

and open the cover.

Insert 4 x 1.5 V AA batteries into the battery compartment.

Please pay careful attention to the polarity, which is marked on the
inside of the battery compartment cover.Otherwise the device will not
work and can be damaged.

Close the battery compartment cover and gently press against it until it clicks

audibly into place.

If you operate the device using a mains adapter (not supplied), open the round

rubber seal on the base plate and connect the plug of the adapter cable into the
socket for the external mains adapter, which is now accessible. The mains
adapter must supply a direct-current voltage of 6 V with at least 680 mA.

Operation via a mains adapter is possible with batteries inserted. If one power
source fails, operation will be maintained using the other.

Video connection

The camera can transfer the video signal to an external monitor or the video
input of a television set.

Connect a suitable monitor to the TV out socket using the supplied TV
cable .

Inserting SD Card

Since the camera has no built-in memory, it can only work if an SD/SDHC

memory card is inserted.

The device supports SD/SDHC memory cards with a capacity of up to 32 GB.

To avoid malfunctions, keep the memory card away from moisture and avoid

strong vibration, dust, heat sources and direct sunlight.

Insert the memory card as indicated by the icon on the slot.

Never force the memory card into the slot. Never bend or twist the
memory card.

After transport, wait until the memory card has reached ambient temperature

before using it for the first time. Major fluctuations in temperature or humidity
can lead to condensation which could cause an electrical short-circuit. Keep the
memory card in the protective case.

To remove an SD/SDHC memory card from the memory card slot of the device,

press the protruding edge of the memory card in a little way until it pops out.
Then remove the card.

Summary of Contents for 8210A





















Reviews: