manualshive.com logo in svg

Best Wi-Q Technology EXQ Series, Installation Instructions Manual, Page: 19 / 20

Share
Download
Best Wi-Q Technology EXQ Series Installation Instructions Manual Download Page 19

Installation Instructions for Wi-Q Technology™ EXQ Exit Hardware Trim

BEST

a Product Group of dormakaba USA Inc.

19

Installation Instructions for Wi-Q Technology™ EXQ Exit Hardware Trim

Completing the installation

19

Install battery/antenna cover

1 

If installing with a surface vertical rod exit device

, 

carefully use a razor blade to remove the knockouts for 
the rod from the battery cover. See Figure 30.

2  Connect the antenna to its mating connector.
3  Coil the antenna wire carefully inside the battery 

cover.

Caution:  

Carefully bend, but do not twist or kink 

the antenna wire. Doing so may significantly 
reduce or completely interrupt signal transmis-
sion.

4 

Making sure that the battery/antenna cover does 
not pinch any wires

, place the battery/antenna cover 

over the bracket and battery.

5  Secure the battery cover with the provided self-tap-

ping screws. 

Caution:  

Tighten screws firmly but do not over-

tighten. Over-tightening may strip screw holes or 
crack the cover.

 Figure 30 Installing the battery cover over the battery 

bracket and connecting the antenna

Battery/ 

antenna cover
Antenna wire

Battery bracket

Carefully bend, 

but DO NOT 

TWIST OR KINK 

the antenna 

wire!

Knockout

Summary of Contents for Wi-Q Technology EXQ Series





















Reviews:

No comments