background image

Method of Installation

1.  Locate and isolate power to distribution panel  

 

where installation is to take place.

2.  Identify the single conductor wire to be  

 

monitored and direction of flow/load.

3.   Attach the current transformer around  

 

the conductor to be monitored without placing  

 

excessive strain or pressure. Do not route the  

 

leads over sharp edges and take care to fit the  

 

CT with the arrow in direction of flow/load.

Notes:

 If you placed the wire in the 

wrong terminal, gently press plastic 
clip with a screwdriver to release  
(as seen in picture above).

If the Analytics platform shows a 
negative kW trace, either reverse the 
black and white leads or reverse the 

direction of current flow through the 

CT’s.

4.  For greater accuracy of measurement it is  

 

advisable to cable tie the conductor to the  

 

CT body so the conductor passes through  

 

the centre of the  CT.

5.  Repeat steps 2 to 4 for the other phases to  

 

be measured.

6.   Now push the CT secondary leads into the  

 

RJ12 adaptor terminals for your phase  

 

type as shown on the next page. The white  

 

cable  of each CT connects to either  

 

terminals 1, 2 and 3 of the side showing the  

 

Best.Energy logo. The corresponding black  

 

cable of each CT connects to terminal of  

 

same number on the opposite side of the  

 

terminal block.

17

[ E N S C O P E   H Y B R I D   M A N U A L ]

Summary of Contents for Eniscope Hybrid





















































Reviews: