BERTHOLD TECHNOLOGIES LB 8300 Operating Manual Download Page 41 | Manualshive

Page: 41 / 58

background image

Rod source shields LB 8300

7 Decommissioning

64217BA2 Rev. 00, 10/2017

41

7

Decommissioning

7.1

Safety instructions

j

WARNING

Danger of injury by falling loads



Never stand underneath a lifted or suspended load, keep at a safe
distance.



Only use tested sling gear components appropriate for the transport

weight.



Exclusively use the provided fixing possibilities (lifting brackets) for
attaching the sling gear.



Wear head protection and safety shoes.

j

CAUTION

Danger of injury caused by heavy and bulky system components



Heavy and bulky system components should only be handled using aids
and by at least 2 persons.



Observe the guidelines for safe handling of heavy loads.



Ensure stability and use the provided fixing possibilities.

j

CAUTION

Danger caused by nuclear radiation
Shields usually contain radioactive sources. An increased exposure to radiation

may lead to damage to health.



Consult the radiation safety officer responsible for your company.



Transport the source exclusively inside the closed and secured shield.

IMPORTANT

The applicable national regulations of the country of use have to be observed.

«
...
39
40
41
42
43
...
»

Summary of Contents for LB 8300



























































Reviews:

No comments

Related manuals for LB 8300

Brand: NEC Pages: 29

Brand: Xoop Lighting Pages: 20

Brand: Vari Lite Pages: 132

Infield Rascal Pro

Brand: ABI Attachments Pages: 8

Brand: Abicor Binzel Pages: 84

Brand: ABI Attachments Pages: 5

Brand: abem Pages: 47

Brand: Abely Pages: 5

Brand: Rangevision Pages: 28

Brand: Nabtesco Pages: 26

Life/form SmartScope LF01142U

Brand: Nasco Pages: 2

Brand: PASCO Pages: 30

Brand: RAMVAC Pages: 53

Alcotest 7410 GLC

Brand: Dräger Pages: 15

Brand: enz Pages: 40

Brand: Furuno Pages: 20

Street Bar IP65 16x3W TW

Brand: Varytec Pages: 52

SkyWriter HPX M-5

Brand: X-laser Pages: 65

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands