BERTHOLD TECHNOLOGIES LB 8300 Operating Manual Download Page 22 | Manualshive

Page: 22 / 58

background image

4 Installation

Rod source shields LB 8300

22

64217BA2 Rev. 00, 10/2017

1
2
3

CLOSED position
Padlock
Transport securing device

Fig. 4

Shield closed (CLOSED position)

1.

Ensure that the shield has been closed and secured



the locking cylinder is set to the CLOSED position



the transport securing device and, if applicable, the padlock are installed

j

WARNING

Danger of injury by falling loads
Falling loads can endanger people.



Never stand underneath a lifted or suspended load, keep at a safe

distance.



Cordon off the danger zone with barrier tape.

j

WARNING

Danger of crushing by moving the shields
Due to the high weight of the shield, there is a risk of injury.



Heavy and bulky system components should only be handled using aids
and by a at least 2 persons.



Do not reach between the shield and the container or mounting base.

«
...
20
21
22
23
24
...
»

Summary of Contents for LB 8300



























































Reviews:

No comments

Related manuals for LB 8300

Brand: Keithley Pages: 149

Brand: Cadman Pages: 66

Brand: UNIA Pages: 62

Brand: Tascam Pages: 8

Brand: Idex Pages: 141

Brand: IDEAL Networks Pages: 8

Brand: IDEAL Networks Pages: 5

Brand: olympia electronics Pages: 4

Brand: Parker Pages: 64

Brand: Parker Pages: 40

Matrx Digital MDM

Brand: Parker Pages: 20

Brand: Parker Pages: 52

Brand: Hach Pages: 456

Brand: M-Audio Pages: 3

Brand: Xtralis Pages: 26

AirForm Night Splint

Brand: Össur Pages: 16

Brand: Össur Pages: 17

Brand: v.link Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands