BERTHOLD TECHNOLOGIES LB 8300 Operating Manual Download Page 42 | Manualshive

Page: 42 / 58

background image

7 Decommissioning

Rod source shields LB 8300

42

64217BA2 Rev. 00, 10/2017

7.2

Disassemble the shield

j

WARNING

Danger of injury by falling loads
Falling loads can endanger people.



Never stand underneath a lifted or suspended load, keep at a safe

distance.



Cordon off the danger zone with barrier tape.

j

WARNING

Danger of crushing by moving the shields
Due to the high weight of the shield, there is a risk of injury.



Heavy and bulky system components should only be handled using aids
and by a at least 2 persons.



Do not reach between the shield and the container or mounting base.

1
2
3

Position CLOSED
Ring nuts
Screw connection

Fig. 16

Dissasemble the shield

1.

Ensure that the shield has been closed and secured.



the locking cylinder is set to the CLOSED position



the transport securing device and, if applicable, the padlock are installed.

«
...
40
41
42
43
44
...
»

Summary of Contents for LB 8300



























































Reviews:

No comments

Related manuals for LB 8300

Brand: Campbell Pages: 18

Brand: Vector Pages: 4

Brand: Parker Pages: 5

Brand: Bacharach Pages: 31

Brand: Bacharach Pages: 2

Brand: ZIGBEE Pages: 6

Brand: Daisy Pages: 2

Below Ground Pool Cover Box

Brand: Daisy Pages: 3

Brand: M-Audio Pages: 3

Brand: M-Audio Pages: 12

Brand: M-Audio Pages: 64

Brand: M-Audio Pages: 16

Brand: M-Audio Pages: 4

Brand: M-Audio Pages: 52

Brand: Qlight Pages: 4

Brand: U-Line Pages: 3

Brand: U-Line Pages: 2

Brand: Onwa Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands