BERTHOLD TECHNOLOGIES LB 8300 Operating Manual Download Page 27 | Manualshive

Page: 27 / 58

background image

Rod source shields LB 8300

5 Usage

64217BA2 Rev. 00, 10/2017

27

5

Usage

5.1

Safety instructions

j

CAUTION

Danger caused by nuclear radiation
Shields usually contain radioactive sources. An increased exposure to radiation

may lead to damage to health.



Consult the radiation safety officer responsible for your company.



Ensure that the shield does not show any signs of damage or functional
limitations.



Please observe the instructions on regular maintenance.

5.2

Opening and closing the locking mechanism

The locking mechanism is used for opening and closing the beam path.

IMPORTANT

During transport and installation of the shield, the locking cylinder must be

set to CLOSED and be secured.

IMPORTANT

The locking mechanism may only be operated by persons who are at least

employees with general knowledge and were instructed by an expert or
authorized person. If the shield includes a radioactive source, the responsible
radiation safety officer must be consulted.

Opening the locking mechanism:

1.

If applicable, remove the padlock.

2.

Remove the transport lock.

3.

Turn the locking cylinder to the OPEN position with the help of the lever rod.

4.

Retain the locking cylinder in the new position using fixing screws.



The radiation beam outlet is now open.

«
...
25
26
27
28
29
...
»

Summary of Contents for LB 8300



























































Reviews:

No comments

Related manuals for LB 8300

Brand: ABB Pages: 86

Brand: GE Pages: 698

Brand: 3M Pages: 48

Brand: 3M Pages: 19

Speedglas G5-01

Brand: 3M Pages: 62

Quickfit Nexus Exit

Brand: Thomas & Betts Pages: 2

Brand: Velocitek Pages: 81

ABS-Lock X-Flat

Brand: ABS Pages: 8

ABS-Lock X-DURCH

Brand: ABS Pages: 8

Brand: ABS Pages: 8

Brand: ACDC Pages: 4

Brand: Mainca Pages: 21

Brand: Daktronics Pages: 30

Brand: DAKOTA ULTRASONICS Pages: 28

Brand: Pari Pages: 50

Brand: Icare Pages: 42

Brand: zapco Pages: 14

Brand: V-GREAT Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands