background image

 

 

 

22 

890053-03-01 

Connecting with Other Products 

 

 

Instance  Byte 

Bit 7 

Bit 6  Bit 5 

Bit 4 

Bit 3 

Bit 2 

Bit 1 

Bit 0 

 

Speed Actual (Low Byte) 

– Hz unit (note 1) 

Speed Actual (High Byte) 

– Hz unit 

111 

At 

Reference 

Ref 

From 

Net 

Ctrl 

From 

Net 

Ready 

Running 

2 (Rev) 

Running

1 (Fwd) 

Warning  Faulted 

Drive State 

Speed Actual (Low Byte) 

– Hz unit 

Speed Actual (High Byte) 

– Hz unit 

141 

Status Parameter - 1 data (Low Byte) 

Status Parameter - 1 data (High Byte) 

142 

Status Parameter - 1 data (Low Byte) 

Status Parameter - 1 data (High Byte) 

Status Parameter - 2 data (Low Byte) 

Status Parameter - 2 data (High Byte) 

143 

Status Parameter - 1 data (Low Byte) 

Status Parameter - 1 data (High Byte) 

Status Parameter - 2 data (Low Byte) 

Status Parameter - 2 data (High Byte) 

Status Parameter - 3 data (Low Byte) 

Status Parameter - 3 data (High Byte) 

144 

Status Parameter - 1 data (Low Byte) 

Status Parameter - 1 data (High Byte) 

Status Parameter - 2 data (Low Byte) 

Status Parameter - 2 data (High Byte) 

Status Parameter - 3 data (Low Byte) 

Status Parameter - 3 data (High Byte) 

Status Parameter - 4 data (Low Byte) 

Status Parameter - 4 data (High Byte) 

145 

Status Parameter - 1 data (Low Byte) 

Status Parameter - 1 data (High Byte) 

Status Parameter - 2 data (Low Byte) 

Status Parameter - 2 data (High Byte) 

Status Parameter - 3 data (Low Byte) 

Status Parameter - 3 data (High Byte) 

Status Parameter - 4 data (Low Byte) 

Status Parameter - 4 data (High Byte) 

Status Parameter - 5 data (Low Byte) 

Status Parameter - 5 data (High Byte) 

146 

Status Parameter - 1 data (Low Byte) 

Summary of Contents for RSi H2 Series


















































Reviews: