BendPak PL-6000DC Installation And Operation Manual Download

Page: 1 / 88

1645 Lemonwood Dr.

Santa Paula, CA 93060 USA

Toll Free: (800) 253-2363

Tel: (805) 933-9970

bendpak.com

Two-Post Parking Lift

Installation and Operation Manual

Manual P/N 5900273 — Manual Revision A1 — May 2022

Model:

•

PL-6000DC

Designed and engineered by BendPak Inc. in Southern California, USA. Made in China.

⚠

DANGER

IMPORTANT SAFETY INSTRUCTIONS, SAVE THESE
INSTRUCTIONS!

Read the entire contents of this Manual

before

installing, operating, servicing, or maintaining this product. Failure to
follow the instructions and safety precautions in this Manual can result in

serious injury or death. Make sure all other operators also read this

Manual. Keep the Manual near the product for future reference.

proceeding with installation and operation, you agree that you

fully understand the contents of this Manual and assume full
responsibility for product use

Summary of Contents for PL-6000DC
























































































Search results

Summary of Contents for PL-6000DC

Reviews:

Related manuals for PL-6000DC

Brands by name

Popular brands

BendPak PL-6000DC, Installation And Operation Manual

Search results

Summary of Contents for PL-6000DC

Reviews:

Related manuals for PL-6000DC

Brands by name

Popular brands