LR-60/60P Low-Rise Scissor Lifts
11
P/N 5900337 — Rev. F — December 2020
Select a Site
Keep the following in mind when selecting a site for your Lift:
•
Enough space
. Make sure there is adequate space on all sides, plus enough space
above
for
the Vehicles you will be raising.
Do not install the Lift under low-hanging obstructions
. See
•
Power Unit Location
. The LR-60 Power Unit Stand can be installed on either side of the Lift,
close enough for the Hydraulic Hose to reach. The LR-60
P
Power Unit is installed on a Portable
Stand, which can be easily moved to the desired location on either side of the Lift within reach of
the Hydraulic Hose.
Operators must always have a full, unobstructed view of the Lift.
•
Hose Cover
. The LR-60 comes with a Hose Cover that you can anchor to the ground; it is
54 in / 1,372 mm long. If you plan to use the Hose Cover, make sure to leave enough room
between the Power Unit and the Lift.
•
Operator
. The operator
must
have a full, unobstructed view of the Lift and the Vehicle on it when
raising and lowering Vehicles.
•
Longitudinal Shift
. When you raise the Lift, the geometry of the scissor arms moves the
Platforms up at an angle. The amount of longitudinal shift for the LR-60/60P is approximately 14
inches. Refer to
•
Check for overhead obstructions
. The site must be free of overhead obstructions.
•
Floor
. Do not install or use this Lift on any asphalt surface other than concrete.
•
Concrete specifications
. Do not install the Lift on or within 6 in / 152 mm of expansion seams
or cracked or defective concrete. Make sure the concrete is at least 4.25 inches thick, 3,000 psi,
and cured for at least 28 days (if newly poured). Make sure the floor is defect-free, dry, and level.
⚠
WARNING
Do not install the Lift on a surface with 3° of slope or more. A 3° degree or greater
slope makes the Lift less secure, possibly causing Vehicles to fall, which could lead
to property damage, personal injury, or even death.
•
Power
. You will need a 115 VAC or a 230 VAC power source available near the Power Unit. The
Power Unit ships configured for 115 VAC, but it can be reconfigured to operate on 230 VAC
(requires an Electrician). Refer to
•
Operating temperature
. The Lift is designed to be used between temperatures of 41º to 104ºF
(5º to 40ºC).
•
Outdoor installation
. The Lift
cannot
be installed outside. It is for indoor use only. If you have
the LR-60P, you can move it outside and use it outside temporarily; make sure to keep it
completely moisture free while it is outside.
•
Second floor installs
. Do not install the Lift on a second floor or elevated floor without first
consulting the building architect and getting their permission.
•
Dress properly
. Always wear protective gear when installing the Lift. Leather gloves, steel-toed
work boots, eye protection, back belts, and hearing protection
are mandatory
. Do
not
wear
loose clothing or jewelry; contain long hair; keep hair, clothing, and gloves away from moving parts.
⚠
WARNING
You
must
wear OSHA-approved (publication 3151) Personal Protective Equipment
at all times when installing
the Lift.
Summary of Contents for LR-60
