background image

4

Installation Introduction

200799_1

Before the product can be installed, consideration will need to be given to routing the power supply to the 
fire. This will affect the stages of the installation process. We advise a qualified electrician conduct any 
electrical parts of the installation. 

Note:  A single wall socket is required for the operation of the fire, please refer to the separate fire 

instructions for further information. 

This product has been designed to be installed into a

pre-fabricated

, or existing

Masonry

chimney breast.

Please seek advice from a professional, with reference to the structural integrity of the installation site.

If the product is to be installed into a open chimney or flue, it is important that the chimney/flue is blocked
off to prevent any up/down draughts and falling debris which could restrict and alter the airflow of the
product.

The product should never be sealed into an opening with the use of silicones or adhesives as this can also
alter the airflow and hinder any future servicing of the product.

It is essential to include a lintel at the required height to ensure the appliance does not support the weight
of the finished wall.

A pre-assembled MDF framework has been supplied to ensure that the product is installed at the required
minimum internal clearances for operation. Before commencing with installation please ensure the

Fire

Support Brackets

have been attached to the MDF framework, these set the minimum depth required for

installation-

238mm

. As shown in

Diagram 1

below.

Diagram 

1

Fix the 

2 x Fire Support Brackets 

using 

4 x No.8 x15mm Domed-Head Screws 

into the pre-drilled holes on 

the MDF framework . 2 x per bracket.

Fire Support 

Brackets

MDF 

Framework

For installation into a

pre-fabricated

chimney breast follow the instructions on

Page 5

then continue onto

Page 7.

For installation into a existing

Masonry

chimney breast follow the instruction on

Page 6

then continue onto

Page 7.

MDF

Framework

H

(mm)

W

(mm)

Min Inset

(mm)

Volta 42”

518

1102

Min 238

Volta 32”

518

852

Min 238

Summary of Contents for Pryzm Volta 32















Reviews: