bemodern Pryzm Volta 32 Instructions For Installation Manual Download Page 14

Page: 14 / 14

Maintenance

WARNING: Before any maintenance or whilst cleaning the exterior of the fireplace, the unit should be

disconnected from the power supply until it has cooled down.

Cleaning the Fire & Trim

Cleaning or polishing products are

not

recommended. Fingerprints or other marks on the front glass panel

can be removed by a piece of soft, damp, lint-free cloth with a good quality household glass cleaner.
The front glass panel should always be completely dried with a clean, lint-free cloth or paper towel.

CAUTION:

Abrasive cleaners should not be used on the glass panel or Trim. Liquids should not be sprayed

directly onto any surface of the unit.

Recycling

All cardboard packing is recyclable.

200799_1

Should you have any queries please call Customer Services on 01914300901 or email us at

[email protected].

Summary of Contents for Pryzm Volta 32















Search results

Summary of Contents for Pryzm Volta 32

Reviews:

Related manuals for Pryzm Volta 32

Brands by name

Popular brands

bemodern Pryzm Volta 32, Instructions For Installation Manual

Search results

Summary of Contents for Pryzm Volta 32

Reviews:

Related manuals for Pryzm Volta 32

Brands by name

Popular brands