background image

Technical Documentation 

KSR-V – Capacitor-Bank Protection Relay 

 

Rev. 05 

 

 

18 

5.8  Alarm display 

If  any  alarm  is  configured  to  display  an  alarm  message,  the  following  display  contents  will  be  shown 

whenever  the  alarm  is  triggered.  After  confirming  the  message,  the  old  display  contents  will  be 

reconstructed. 

An alarm message offers the following information : 

 

In the right top corner of the display, the state of all assembled relays is displayed. A dark number on 

bright ground shows a relay which is deactivated, the reverse display (bright number on dark ground) 

shows an activated relay. Relays, which are not assembled, will not be shown here. 

 

The message "ALARM #xx" in the center of the display shows the number of the active alarm. The 

number appears instead of "xx" in this example.  

 

The actual value of the measurement, which is configured to be the source of this alarm. 

If more than one alarm is active, one can switch between them by pressing key "+".  

The right key ("Enter") can be used to confirm the alarm message. After confirmation, the display shows the 

next active alarm or, if there are no more active alarms, resumes work at the same point where it left before 

the  alarm  occurred.  In  general  the  behaviour  of  the  display  alarms  depends  on  the  setting  "reset 

automatic/manual".  

The  confirmation  only  disables  the  alarm  message.  If  any  output  relays  are  configured  for  the  same  alarm 

they are not influenced by the confirmation.  

To enhance visibility and to make recognition of the alarm easier (especially in dark rooms), the backlight of 

the  display  is  toggled  between  full  brightness  and  reduced  brightness,  which  resembles  a  blinking  signal 

light.  

 

 

Summary of Contents for KSR-V




















Reviews: