background image

 
 

www.belson.com

 

 

3 

III    SAFETY  PRACTICES  TO  AVOID  PERSONAL  INJURY 

-Don'ts- 

 

DON’T move your grill while it is in operation or still hot. 

DON'T use an open flame when testing for gas leaks. 

DON'T use charcoal briquettes, wood chips or any flammable material on top or in place of lava rock. 
DON'T store any flammable materials beneath the firebox or in the vicinity of your grill. 

DON'T use the grill for cooking excessively fatty meats or products which promote flare-ups. 

DON'T use natural gas in a unit designated for liquid propane. 

DON'T operate this unit in a building, garage, or any other enclosed area. 

DON'T operate your grill under overhangs or awnings. 

DON'T obstruct the flow of combustion and ventilation air into or out of this unit. 

DON'T use in high wind conditions; high winds may adversely affect burner performances. 

DON'T use vertical tanks. 

 

-Do's- 

 

DO store your grill indoors or covered, be sure to close the tank valve, disconnect the hose from the tank, 

remove the tank from the grill and

 store the L.P. tank outdoors. 

DO use a leak proof approved sealing compound on all joints when connecting or replacing any gas fittings. 

DO fully open the grill hood before lighting your grill. 

DO remove the control knobs and store them indoors for child safety. 

DO obtain safety instructions from your local gas supplier, and post in a prominent location near the area of 

operation.These instructions are to be followed in the event of a gas leak. 

DO operate your unit outdoors.   

DO operate this unit in a well-ventilated area.   

DO position your portable grill away from direct wind.   

DO inspect flexible gas hose prior to each use. If it is evident that there is excessive abrasion or wear, or the 

hose is cut, it must be replaced prior to the unit being put into operation. 

DO use only 40# horizontal propane cylinders (12” diameter, 29” length) supplied with unit. Any other cylinder 

used must be of identical type and must be constructed and marked in accordance with the 
specifications for LP gas cylinders of the US. Department of Transportation (DOT).  

DO properly store propane cylinders outdoors in a well ventilated area out of reach of children.  Disconnected 

cylinders must have threaded valve plugs tightly installed and must not be stored in a building, garage, 
or any other enclosed area.  

Propane gas is highly flammable! 

DO lock both casters when operating the grill unit.

 

DO handle, use, store and transport  LP gas cylinders in accordance with NFPA 58.  

 

 

 

Summary of Contents for MOBILE-II


























Reviews: