background image

 
 

www.belson.com

 

7

 

VII    LIGHTING  INSTRUCTIONS 

 

IMPORTANT: 

Before each use of your grill, inspect the gas hose prior to turning the gas 'ON' If 
there is evidence of cuts, wear, or abrasion, it must be replaced prior to use. Contact  
Customer Service 1-800-323-5664 for replacement parts.  Do not use the unit if the 
odor of gas is present. 

Keep your face and body as far away from the grill as 

possible when lighting. 

 
STEP 1:  Open the hood.  

Do not stand with your head over the grill when lighting burners.

 

STEP 2:  Check all burner control knobs and main gas supply valves are at 'OFF' position. 

STEP 3:  Slowly open the fuel tank to full, by turning to the left (counter-clockwise). 

STEP 4:  Open one burner valve at a time to 'HI' by pushing-in and then turning the control knob to 

the left (counter-clockwise) about 90 degrees until the 'HI' marking is pointing upwards. 

STEP 5:Wait 3 to 5 seconds for gas to fully reach for ignition. 

STEP 6:  Depress (push) red ignitor button. You’ll hear a snapping sound. At the same time a spark 

will be provided at the front of the burner. It may be necessary to press the button 3 to 6 
times until the burner is lit. 

STEP 7:  Repeat STEP 4 through STEP 6 for each burner. After the burners are lit, if one burner 

goes out, the burner will cross-light automatically.  

 

IF THE BURNER FAILS TO LIGHT 

Immediately 

 turn control knobs to 'OFF' to prevent gas buildup. Wait 

5 minutes

 before trying to re-

light by ignitor. If the burner will not light after several attempts (See Section XVII 
"

TROUBLE SHOOTING

" on Pg. 20). 

 

TIP

:  Operate all burners on high for 5 minutes with hood open or until the lava rock  

 

 

becomes hot. Once the lava rock become hot, then turn the burners down to a lower  

 

setting and allow the radiant heat of the rock to provide the heat for cooking. 

 

SHUTTING DOWN UNIT 

Close the liquid propane tank valve and allow burners to burn all gas from the manifold system. Turn 
burner control knobs to 'OFF' position. Make sure no open flames are present, allow unit to cool. 
Disconnect the regulator and insert the safety plug back to the tank. Follow all warnings pertaining 
to storage of propane tanks. (See Section IV "

PROPANE TANK STORAGE, HANDLING AND 

FILLING"

 Pg. 4). 

 
 
 
 
 
 
 
 

Summary of Contents for MOBILE-II


























Reviews: