10
Blade Adjustment
GB
Transportation
GB
The blade pitch control knob is at easy reach of the operator. The pitch adjustment has an unlimited pitch variation and this can
EHXQGHUWDNHQZKHQHYHUQHFHVVDU\'XULQJ¿QLVKLQJVHWWLQJXSKDUGHQLQJPD\YDU\IURPDUHDWRDUHDDFURVVWKHÀRRUVRWKHSLWFK
adjustment can be changed to suit accordingly while the machine is in operation. When transporting the trowel on a truck, always
NHHSEODGHVIXOO\KRUL]RQWDOÀDWRQWKHÀRDWLQJGLVF
For transportation of the machine use lifting eye. Alternatively to lift the machine, use an aid equipment through the stationary ring, which
can carry the weight of the machine ,with a carrying pipe on the back past of handle.
Troubleshooting Guide
GB
Servicing
GB
Gearbox
&KHFNRLOOHYHOHYHU\PRQWK2QVLGHRIWKHJHDUER[WKHUHLVDQSOXJ8VH³6+(//20$/$PO´JHDURLORUHTXLYDOHQW
Machine Cleaning
&OHDQWKHPDFKLQHDIWHULWKDVEHHQXVHGWRSUHYHQWWKHFROOHFWLRQRIKDUGHQHDUGFRQFUHWHFHPHQWSDVWHLVYHU\GLI¿FXOW
to remove. To clean it use an old brush or hand brush.
Changing of Blades
Be careful when changing old blades with new. Due to the way the blades wear, the old blades become very sharp, like a knife
blade. As a safety precaution very heavy-duty gloves during this operation to prevent the hands being cut. Remove bolts and lock
ZDVKHUVRQHDFKWURZHODUPDQGUHPRYHWKHEODGHV%HIRUHLQVWDOOLQJQHZEODGHVFOHDQDOOFRQFUHWHFHPHQWIURPERWWRPDQGVLGH
of the trowel, be sure trowelling edge of the blade is behind trowel arm. Install bolts and lock washers on each trowel arm and
fasten securely.
Tightening the V-Belts
,I\RXQRWLFHDORRVHRQ9EHOWFKHFNWKHWLJKWQHVV(VSHFLDOO\LQ¿UVWXVLQJDQG9EHOWFKDQJH&KHFNWKH9EHOWWLJKWQHVVDIWHU
KRXUVODWHU8VLQJ\RXUKHDG¿QJHUSXVKWKH9EHOWIURPLWVPLGGOHSRLQW,WPXVWVWUHWFKDERXWFP,ILWVWUHWFKHVPRUHLWLVORRVH
)RUWLJKWHQLQJORRVHWKHPRWRU¿[LQJVFUHZVWLOOPRWRUPRYHVDZD\RQWKHWDEOH/RRVHWKHPRWRUORFNQXW/RRVHWKHVFUHZVSXVK
the motor backward. Checking the V belt tightness, do the same operations. Until tightness of V belt is desired value, screw the
PRWRUOXFNQXWDQGWKHQVFUHZWKHPRWRU¿[LQJVFUHZV
Problem Cause
Remedy
Engine will not start.
No fuel getting to engine.
Open fuel tap.
Fill fuel tank.
Engine switched off.
Switch engine on.
Spark plug fouled.
Clean, check and reset plug gap.
Engine cold.
Close choke.
(QJLQHÀRRGHG
2SHQFKRNHIXOO\RSHQWKURWWOHSXOOUHFRLOVWDUWHUXQWLOHQJLQH¿UHV
Cutout switch wire
Reconnect disconnected wire.
Leaving Swirls in
Main Shaft damaged.
Check and replace as necessary.
concrete, Rolling
Spider Plate arms bent.
Replace as necessary.
Concrete or Bouncing.
Blades are unevenly adjusted.
Check and adjust as necessary.
Blades are all different sizes.
Replace, ensuring all blades are the same size.
Blades are worn.
Replace blades.
