background image

vi

Notices

Mesures de sécurité et avis importants

La présente section fournit des consignes de sécurité importantes pour les opérateurs et le 
personnel de service. Des avertissements ou mises en garde spécifiques figurent dans le 
manuel, dans les sections où ils s’appliquent. Prenez le temps de bien lire les consignes et 
assurez-vous de les respecter, en particulier celles qui sont destinées à prévenir les 
décharges électriques ou les blessures.

Signification des symboles utilisés

Signale la présence d’une tension élevée et dangereuse dans le boîtier de 
l’équipement ; cette tension peut être suffisante pour constituer un risque de 
décharge électrique.

Avertit l'utilisateur, l’opérateur ou le technicien de maintenance que des 
instructions importantes relatives à l'utilisation et à l'entretien se trouvent dans 
la documentation accompagnant l’équipement.

Invite l'utilisateur, l’opérateur ou le technicien de maintenance à prendre note du 
calibre du fusible lors du remplacement de ce dernier. Le fusible auquel il est fait 
référence dans le texte doit être remplacé par un fusible du même calibre.

Identifie une borne de mise à la terre de protection. Il faut relier cette borne à la 
terre avant d’effectuer toute autre connexion à l’équipement.

Identifie une borne de mise à la terre externe qui peut être connectée en tant 
que borne de mise à la terre supplémentaire. 

Signale la présence de composants sensibles à l’électricité statique et qui sont 
susceptibles d’être endommagés par une décharge électrostatique. Utilisez des 
procédures, des équipements et des surfaces antistatiques durant les 
interventions d’entretien.

Le symbole ci-contre signifie que l’appareil comporte plus d’un cordon 
d'alimentation et qu’il faut débrancher tous les cordons d'alimentation avant 
toute opération d’entretien, afin de prévenir les chocs électriques.

La marque C-CSA-US certifie que l’appareil visé a été testé par l'Association 
canadienne de normalisation (CSA) et reconnu conforme aux exigences 
applicables en matière de sécurité électrique en vigueur au Canada et aux États-
Unis.

La marque C-UL-US certifie que l’appareil visé a été testé par Underwriters 
Laboratory (UL) et reconnu conforme aux exigences applicables en matière de 
sécurité électrique en vigueur au Canada et aux États-Unis.

Summary of Contents for Grass Valley LUMO








































































Reviews: