Belden Grass Valley LUMO User Manual Download

Page: 26 / 71

LUMO Housing Frame

Specifications

•

Disconnect the fan power by grasping the connector and pulling straight out.

•

Remove the two screws that secure the fan unit to the frame and pull the fan unit away
from the frame.

•

Retain the screws, as they will be used with the replacement fan.

3 Install the replacement fan:.

•

Use the two screws that were retained when the old fan was removed to install the new
fan onto the rear panel. See the note above.

•

Grasp the power connector attached to the fan assembly, and push it onto the power
outlet located to the left of the fan on the rear panel

Specifications

MECHANICAL

Dimensions

1RU x 17.60” W (447 mm) x 10” D (254 mm) without fiber support

1RU x 17.60” W (447 mm) x 20.25” D (515 mm) with fiber support
with connectors

Weight:

8.9 lbs (4.45 kg) with 1 PSU and controller card installed

POWER

Rating:

100-240V~

0.83 - 0.42 A

Summary of Contents for Grass Valley LUMO








































































Search results

Summary of Contents for Grass Valley LUMO

Reviews:

Related manuals for Grass Valley LUMO

Brands by name

Popular brands

Belden Grass Valley LUMO, User Manual

Search results

Summary of Contents for Grass Valley LUMO

Reviews:

Related manuals for Grass Valley LUMO

Brands by name

Popular brands