Belden Grass Valley LUMO User Manual Download Page 19

Page: 19 / 71

LUMO

User Manual

LUMO-BNC Rear Panel

LUMO-DIN Rear Panel

The functionality of Ethernet connectors is described in the Controller card chapter.

The details of the rear panel card lexans vary depending on the card type, and are described in
Chapter 5.

Installation

Unpacking

Make sure the following items have been shipped with your LUMO frame:

•

LUMO-BNC or LUMO-DIN frame, including 1 Power Supply unit (AC in) and 1 Status card

•

If the optional LUMO CPU-ETH controller has been ordered, the Status card is not
included

•

Rack-mounting brackets (1 pair, with 8 mounting screws)

•

An AC power cord

•

Power cord retaining clips (2)

•

LUMO-series cards (per order) with associated lexans

•

Fiber Support with 8 mounting screws (standard or MPO version)

•

LUMO controller card (optional)

•

A second power supply and AC cord (optional)

Summary of Contents for Grass Valley LUMO








































































Search results

Summary of Contents for Grass Valley LUMO

Reviews:

Related manuals for Grass Valley LUMO

Brands by name

Popular brands

Belden Grass Valley LUMO, User Manual

Search results

Summary of Contents for Grass Valley LUMO

Reviews:

Related manuals for Grass Valley LUMO

Brands by name

Popular brands