Bedrock SM30 Operating Manual Download Page 72 | Manualshive

Page: 72 / 101

Bedrock SM30 Operating Manual Download Page 72

72

Bedrock SMxx operating manual

© Bedrock Audio BV, 2019

14. Cleaning, maintenance and
calibration

With normal use, no further maintenance is needed beyond normal cleaning periodic re-
calibration of the device. We recommend that you have the device checked and calibrated
at our factory or at an external calibration specialist at least once every 2 years.

We recommend having the battery pack replaced after approx. 500 charge/recharge cycles,
or once every 4 years.

We recommend that you clean the instrument with a soft cloth. LCD display cleaner can be
used to clean the touch screen, provided that the following precautions are taken:

•

Do not spray cleaner directly onto the display

•

Only use cleaning liquids specifically intended for LCD screens

Battery disposal

The device contains a 4.8v rechargeable NiMH battery pack. At the end of
the life cycle of this product, care should be taken to dispose of this battery
pack responsibly, in compliance with rules and regulations for recycling of
batteries that apply in your region. MAKE SURE THAT THIS BATTERY
PACK IS REMOVED BEFORE DISPOSING OF THE DEVICE. If you
are unable to remove the battery pack yourself (by unscrewing the back lid
of the device), make sure that you mention the presence of an NiMH battery
pack when handing in the entire device for recycling.

«
...
70
71
72
73
74
...
»

Summary of Contents for SM30






































































































Reviews:

No comments