manualshive.com logo in svg

Bedrock SM30, Operating Manual, Page: 58 / 101

Share
Download
Bedrock SM30 Operating Manual Download Page 58

 

    58 

 

 

 

 

 

Bedrock SMxx operating manual 

      

 

     © Bedrock Audio BV,  2019 

 

 

 

    

10.2. Settings

The settings module allows you to configure the overall settings of the device, in addition 
to the module-specific settings found in each module. The following attributes can be set:

• 

Time and date (time in 24h format and date in DD-MM-YYY format)

• 

Calibration of the touch screen digitizer (use with caution)

• 

Phantom power to the microphone

• 

Microphone type selection

• 

Microphone pre-amplifier gain (measuring range)

• 

Time  interval before the backlight automatically switches off to save power

• 

Brightness of the display (

not available on early versions of the SM50

)

• 

Recording of audio during measurements (on / off)

• 

Text annotations with each measurement (on / off)

The system date and time are changed by means of the arrows (up/down). Note that your 
changes are not applied until you press “set clock.”

Date and time in the settings module

The Bedrock SMxx has an internal real-time clock that keeps running even when the de-
vice is powered off. The clock needs to be adjusted if the battery has been depleted com-
pletely, for instance when the device has not been used for a very long time.  The system 
date and time are used for time-stamping the saved data. If you download measurement 
data over USB, the file creation date/time are only accurate if the internal real-time clock of 
the device was updated  to the right date and time.

Use the “calibrate touch”function if the response of the touch screen appears to be inac-
curate.  Calibration takes place by pressing exactly on the indicated marks near the corners 
of the screen. Note that touch calibration is needed very rarely; do not activate this function 
unless you are experiencing a reduced accuracy of the touch screen digitizer.

Summary of Contents for SM30






































































































Reviews:

No comments