manualshive.com logo in svg

Bedrock SM30, Operating Manual, Page: 3 / 101

Share
Download
Bedrock SM30 Operating Manual Download Page 3

 

    2 

 

 

 

 

 

Bedrock SMxx operating manual 

      

 

     © Bedrock Audio BV,  2019 

 

 

 

    

3

Contact information and support

The Bedrock SMxx devices (SM30, SM50, SM90) are designed and manufactured by Em-
bedded Acoustics B.V. in the Netherlands.

The manufacturer can be contacted at the following address:

Bedrock Audio BV
Ampèreweg 18
2627 BG DELFT
The Netherlands
www.bedrock-audio.com
Phone: +31 88 8770700
Fax: +31 88 8770799
Email: [email protected]

Updates of the system’s firmware and documentation are released online :

www.bedrock-audio.com/support

NOTE: All screenshots and product pictures shown in this manual correspond to the 
SM50 with hardware platform 1.1B running firmware version 2.4. If you are using a differ-
ent device model or a different firmware version, the screenshots may not fully correspond 
to what is being displayed on your device’s screen.

Where this manual refers generically to the Bedrock SMxx,  the corresponding text ap-
plies to all device models starting with the letters “SM” (i.e. SM30, SM50 and SM90).

All functions and features of the SM30 are identical to the SM50, with the exception of 
the STIPA modules (which are not featured on the SM30). The SM90 hardware differs 
from the other two models: it complies with Type 1/ Class 1 requirements (compared to 
Type 2 / Class 2 for the other models).

© Bedrock Audio BV, 2013-2019. All rights reserved.
Bedrock Audio and Embedded Acoustics are registered trademarks.

Document version 2.4.0 release date April 2019. Applies to models: SM30, SM50 and 
SM90. Speech intelligibility related functions not supported on SM30

Summary of Contents for SM30






































































































Reviews:

No comments