Bedfont FENObreath User Manual Download Page 52

Page: 52 / 65

Possible

Cause

Recommended

Action

The drying

cartridge is

missing or

disconnected

Take the back

cover off and

check drying

cartridge is

present and fully

located into the

device. Replace

the back cover.

The NO

scrubber is

missing or

disconnected

Take the back

cover off and

check NO scrubber

is present and fully

located into the

device. Replace

the back cover.

Possible Cause

Recommended Action

If the patient

exhales

outside of the

exhalation

guidelines,

the test will beep

before indicating

a fail and a red

cross will appear.

Press the retry icon to

retake the test or if

after multiple attempts

the patient is unable to

comply, the reading can

be viewed by pressing

the next arrow.

WARNING:

Patients should exhale for the duration of time

indicated by the monitor during a breath test. Failure to do

so could impact the reading.

The device consistently reads 0ppb

Summary of Contents for FENObreath


































































Search results

Summary of Contents for FENObreath

Reviews:

Related manuals for FENObreath

Brands by name

Popular brands

Bedfont FENObreath, User Manual

Search results

Summary of Contents for FENObreath

Reviews:

Related manuals for FENObreath

Brands by name

Popular brands