Beckman Coulter CEQ 8000 series Troubleshooting Manual Download Page 32 | Manualshive

Page: 32 / 50

background image

Section III: Sequencing Troubleshooting Quick Reference Table

28

CEQ™ 8000 Series Genetic Analysis System

Low Raw Signal and
Erratic or Crashed
current profiles

Preheat treatment on plasmid
samples was not performed
(plasmid/cosmids/YAC/BAC/
PAC samples).

Preheat all plasmids templates

The preheat treatment was
carried out with all the
sequencing reagents added.

Preheat ONLY the DNA and WATER

The cycling program had an
extra step in the beginning for
the preheat treatment.

Do not

add an extra step in the

beginning of the cycling program

Too much DNA loaded onto
capillaries.

Reduce the amount of DNA—follow
protocol recommendations

Sample contains
contaminating ions that are
injected onto capillaries- (ions
from contaminating salts, bad
formamide etc.).

Check method of DNA purification

Incorrect method of template
purification e.g.- CsCl,
Phenol/Chloroform, or
insufficient removal of
Ethanol during template
preparation etc.

Refer to the CEQ 2000 DTCS
chemistry Protocol, 718119-AB, pg.
18 and Application Note A-1872A for
detail on the preheat treatment
procedure.
Use supplied SLS for sample
resuspension

No signal associated
with normal
Current Profile

(No signal even from
the Unincorporated
dyes)

Lost Pellet

Use “gel loading pipette tips” to
remove ethanol during precipitation

Tips of capillary broken

Replace capillary array if tips are
broken

ddNTPs not added

Check that all reagents were added

Sample not resuspended in
formamide

Only use SLS for sample resuspension

Not enough sample in well
(though in most cases will see
a current problem)

Use at least 30µl of SLS to resuspend
the samples

PROBLEM

RAW DATA

SIGNAL /

CURRENT

PROFILE

POTENTIAL SOURCE OF

PROBLEM

POSSIBLE SOLUTIONS

«
...
30
31
32
33
34
...
»

Summary of Contents for CEQ 8000 series



















































Reviews:

No comments

Related manuals for CEQ 8000 series

Brand: Yamaha Pages: 8

Brand: 3M Pages: 2

Brand: 3M Pages: 16

Brand: KROHNE Pages: 34

Brand: YOKOGAWA Pages: 53

Brand: Keller Pages: 4

FG-3000R Series

Brand: Nidec Pages: 8

Brand: E+E Elektronik Pages: 32

KINGFISHER PLUS+

Brand: semaphore Pages: 247

NOVAplus biogas

Brand: mru Pages: 78

Brand: Z-TRAUQ Pages: 10

Brand: Hanna Instruments Pages: 12

Brand: A&D Pages: 2

Brand: Hammond Pages: 106

Brand: Omega Pages: 59

Brand: TESTO Pages: 2

Brand: East Tester Pages: 36

NADAL Borreliosis Ag Test

Brand: nal von minden Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands