manualshive.com logo in svg

Beckman Coulter Avanti J-E, Instruction Manual

Share
Download
Beckman Coulter Avanti J-E Instruction Manual Download Page 56

5-4

Maintenance

While Beckman Coulter has tested ethanol (70%) and found that it 
does not damage the centrifuge, no guarantee of sterility or disinfec-
tion is expressed or implied. When sterilization or disinfection is a 
concern, consult your laboratory safety officer regarding proper 
methods to use.

REPLACING THE AIR FILTER

Check the air filter (Figure 5-1) regularly and replace it about once a 
year, or more often if it looks dirty. The air filter is not fastened to the 
centrifuge, so no tools are required for removal or installation. 

1. To remove the air filter, grasp the top edge and lift the filter 

straight up.

2. Install a new filter by holding the top edge and inserting the 

bottom edge into the slot in the air deflector strip. Lower the filter 
until the bottom edge rests on the brackets.

Figure 5-1. Air Filter Replacement

Air Deflector

Filter Brackets

Filter

Summary of Contents for Avanti J-E

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands