background image

Commissioning and configuration

EP9224-0037

38

Version: 1.0

Evaluate recorded measured values

The recorded measured values are available as a .csv file. The file must be uploaded from the box to the
control computer in order to be able to evaluate it.

Proceed as follows to upload the recorded measured values to the control computer:

1. Double-click on the EP9224-0037 IO module in the IO tree.

2. Click on the 

Online

 tab.

3. Click on the 

Upload

 button.

ð

A dialog box with the title "Save As" appears.

4. Select a directory and write in the field 

File Name:

     „logdata.csv“

5. Click on the 

Save 

button.

ð

A dialog box appears with the title "Edit FoE Name".

6. Click 

OK

.

ð

The file with the measured values was uploaded to the control computer.

File format

The file with the measured values begins with a header "**** Logfile from Ethercat Slave ****".

Below that follow

• a file header

• a measured value table

Format of the file header:

Field

Description

Device Name

Name of the module

File Version

Version number
(Note: when importing from EXCEL the version, e.g. 1.5, is
interpreted/displayed as a date (1st May))

Reason for which the snapshot was
taken

Reason for stopping the data logger

Age of snapshot

time elapsed from stopping the data logger until the upload

System timestamp (0 if DC not
supported)

current timestamp when uploading

Format of the measured value table:

Type

Description

Time offset additional to snapshot age

The age of the measured values in the row in relation to the
stopping of the data logger (0 = stop, > 0 older values) in ms

I(U...)

present current values of the channels Us / Up 1 - 4 in 100 mA

Internal Temperature

internal module temperature in °C

Us / Up

Input voltage Us and Up at the 7/8" input in V

Sum Current Us / Up

Sum current of Us and Up in A

I²t(U...)

virtual overload, incremented or decremented depending on the
nominal current

• from 10% warning

• at 100% shut-off

Summary of Contents for EP9224-0037

































































Reviews: