Beckhoff EP9224-0037 Documentation Download Page 25 | Manualshive

Page: 25 / 64

background image

Mounting and cabling

EP9224-0037

25

Version: 1.0

3.6

Cabling

For connecting EtherCAT devices only shielded Ethernet cables that meet the requirements of at least
category 5 (CAT5) according to EN 50173 or ISO/IEC 11801 should be used.

EtherCAT uses four wires for signal transmission.
Thanks to automatic line detection ("Auto MDI-X"), both symmetrical (1:1) or cross-over cables can be used
between Beckhoff EtherCAT.

Detailed recommendations for the cabling of EtherCAT devices can be found at

https://infosys.beckhoff.com/content/1033/ethernetcabling/index.html?id=1661412216745722148

«
...
23
24
25
26
27
...
»

Summary of Contents for EP9224-0037

































































Reviews:

No comments

Related manuals for EP9224-0037

Brand: Atlas Pages: 8

Brand: ttaf Pages: 4

Brand: Pentair Pages: 2

Brand: EuroLite Pages: 15

Brand: EuroLite Pages: 15

Brand: EuroLite Pages: 16

KingMi QMCXB33CH

Brand: Xiaomi Pages: 2

Brand: Magnet Pages: 24

Brand: Jedia Pages: 11

Brand: Unika Pages: 4

Brand: CYP Pages: 12

Brand: PFPower Pages: 1

Brand: Tripp Lite Pages: 2

Power Distribution Modules SUPDM Series

Brand: Tripp Lite Pages: 2

Brand: Tripp Lite Pages: 4

Brand: Tripp Lite Pages: 4

Brand: Tripp Lite Pages: 4

Brand: Tripp Lite Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands