manualshive.com logo in svg

Beckhoff CU8130-0240, Manual, Page: 9 / 57

Share
Download
Beckhoff CU8130-0240 Manual Download Page 9

Safety

CU8130-0240

9

Version: 1.1

Assembly

• Never work on live equipment. Always switch off the power supply for the device before installation,

troubleshooting or maintenance. Protect the device against unintentional switching on.

• Avoid polarity reversal of the data and supply cables, as this may cause damage to the equipment.

• Observe the relevant accident prevention regulations for your machine (e.g. the BGV A 3, electrical

systems and equipment).

• Note the temperature limit values for operation. If the UPS is operated outside of these temperature

limit values, electrolyte can escape, heat up or in the worst case explode.

• The UPS location must be adequately ventilated. In case of a fault, the UPS can release flammable

gases that could cause an explosion.

• Do not store the UPS in an airtight container or bag. The battery pack can release gases that could

explode if the UPS is kept in an airtight enclosure.

• If you come into contact with electrolyte, rinse the affected body part immediately with water.

Firefighting

Extinguish the battery pack with dry powder, halon or CO

2

.

• Do not extinguish with water.

• Disconnect the power supply.

• During firefighting wear self-contained respiratory protective equipment and protective clothing.

• Air the room after you have extinguished the UPS.

Safety labels on the UPS

The following safety labels are attached to the name plate of the UPS:

Summary of Contents for CU8130-0240


























































Reviews:

No comments