Beckhoff CU8130-0240 Manual Download | Manualshive

Page: 48 / 57

background image

Decommissioning

CU8130-0240

48

Version: 1.1

10

Decommissioning

10.1

Dismantling the UPS

NOTE

Electrical voltage

If the power supply is switched on during dismounting, this can lead to damage to the UPS. Switch off the
power supply during dismounting.

This chapter shows how to disassemble the UPS and thus remove it from the DIN rail. Shut down the
industrial PC connected to the UPS so that the UPS is switched off.

Requirements:

• Switch off the power supply.

Dismantle the UPS as follows:

1. Push the UPS upwards.

ð

As soon as you push the UPS upwards, the lower springs of the DIN rail adapters give way. This
allows the UPS to be released from the top edge of the DIN rail.

2. Tilt the UPS forwards.

ð

The UPS can be removed from the DIN rail.

«
...
46
47
48
49
50
...
»

Summary of Contents for CU8130-0240


























































Reviews:

No comments

Related manuals for CU8130-0240

Brand: jbc Pages: 20

Brand: Westfalia Pages: 34

Brand: Baileigh Industrial Pages: 56

Brand: RIDGID Pages: 40

KH 3163 POWER SCRAPER

Brand: Parkside Pages: 28

Brand: Teccpo Pages: 16

Brand: Grizzly Pages: 2

Brand: PASCO Pages: 36

SBP-XFMR Series

Brand: ECO POWER Pages: 21

sunjoe24V-HG100

Brand: SNOWJOE Pages: 52

Brand: National Instruments Pages: 47

Brand: Stanley Pages: 233

Brand: stayer Pages: 40

Brand: 9circle Pages: 4

Big-O-Matic 90130

Brand: Schulze Pages: 17

Brand: Würth Pages: 227

Brand: Clearaudio Pages: 12

Brand: Parkside Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands