manualshive.com logo in svg

Beckhoff CU8130-0240, Manual, Page: 49 / 57

Share
Download
Beckhoff CU8130-0240 Manual Download Page 49

Decommissioning

CU8130-0240

49

Version: 1.1

10.2

Disposal

Beckhoff Automation products are marketed exclusively to corporate customers. According to the directive
2012/19/EU "WEEE", we take old devices and accessories back for professional disposal. The transport
costs are covered by the sender.

Send the old devices with the note "For disposal" to:

Beckhoff Automation GmbH & Co. KG
Gebäude „Service“
Stahlstraße 31
D-33415 Verl

Replacement battery modules

CU9900-U015 and CU9900-U030 replacement battery modules for CU8130 UPS modules from Beckhoff
Automation GmbH & Co. KG are marketed exclusively to corporate customers. According to the German law
on batteries (BattG), we take old batteries back and pass them on to a disposal company. The transport
costs are covered by the sender.

Send the old battery with the note "For disposal" to:

Beckhoff Automation GmbH & Co. KG
Building "Service“
Stahlstraße 31
D-33415 Verl

The packaging of the replacement battery can be used to return the old battery.

Summary of Contents for CU8130-0240


























































Reviews:

No comments