Beckhoff CU8130-0240 Manual Download | Manualshive

Page: 52 / 57

background image

Appendix

CU8130-0240

52

Version: 1.1

12

Appendix

12.1

Accessories

Table 17: Spare battery module.

Order number

Description

C9900-U0300

Spare battery module, 30 Wh, suitable for CU8130-0240

Table 18: Installation accessories.

Order number

Description

C9900-M675

Mounting plate made of black anodized aluminium for mounting the UPS on the
control cabinet wall, suitable for CU8110-0120, CU8130-0120 and CU8130-0240

C9900-P950

Spare connectors for the power supply of the CU81xx UPS series. Two 9-pin
connectors with push-in connection for cables with a cross-section of 0.14 mm²
to 1.5 mm² or AWG26 to AWG16.

C9900-K552

connecting cable USB 2.0 A-B, 3 m

C9900-K553

connecting cable USB 2.0 A-B, 5 m

C9900-K554

connecting cable USB 2.0 A-B, 1 m

«
...
50
51
52
53
54
...
»

Summary of Contents for CU8130-0240


























































Reviews:

No comments

Related manuals for CU8130-0240

Brand: MAKER MADE Pages: 14

Brand: National Flooring Equipment Pages: 44

Brand: Earlex Pages: 12

Brand: Earlex Pages: 12

Brand: Earlex Pages: 4

Brand: Earlex Pages: 4

Brand: IBM Pages: 66

Brand: Palmgren Pages: 12

Brand: RAMSET Pages: 16

Brand: Marson Pages: 11

Brand: Hama Pages: 56

Brand: WAGO Pages: 44

Brand: ITech Pages: 103

Brand: Rivtec Pages: 4

Brand: Graco Pages: 10

Brand: ADC Pages: 4

Brand: General International Pages: 52

Brand: YASKAWA Pages: 31

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands