Beckhoff AM8000 Series Operation Instructions Manual Download Page 99

Page: 99 / 123

Electrical installation

Version: 4.3

───

AM8000 and AM8500

9.1.3

Connectors

9.1.3

► Push iTec connector [2] straight onto power box [1] of the motor

► Make sure that the marking points face each other

► Pay attention to the "click" sound

► Make sure that all marking points [3] are in alignment

The iTec connector is then fully engaged.

Important

If the iTec connector does not automatically lock into place on the
power box during the rotational movement:

► Turn the iTec connector by hand into the correct position so that

the marking points [3] are aligned

9.1.4

Rotary joints

9.1.4

► Push speedtec connector [2] straight onto power box [1] of the

motor

► Make sure that the marking arrows face each other

► Turn the cap nut [3] clockwise

Summary of Contents for AM8000 Series




























































































































Search results

Summary of Contents for AM8000 Series

Reviews:

Related manuals for AM8000 Series

Brands by name

Popular brands

Beckhoff AM8000 Series, Operation Instructions Manual

Search results

Summary of Contents for AM8000 Series

Reviews:

Related manuals for AM8000 Series

Brands by name

Popular brands