Beckhoff AM8000 Series Operation Instructions Manual Download Page 116

Page: 116 / 123

Decommissioning

116

───

Version: 4.3

AM8000 and AM8500

Disassembly may only be carried out by qualified and trained per-
sonnel.

Read the chapter Documentation notes.

When disposing of electronic waste, make sure that you dispose of
it in accordance with the regulations applicable in your country.
Read and follow the instructions for proper disposal.

14.1

Disassembly

WARNING

Risk of injury from leaking oil

Prevent oil from leaking. Let it cool down before starting work.
Soak up any leaked oil with approved binding agents. Mark the
danger spot.

Leaking oil can cause slips and falls, resulting in serious or fatal
injury. Hot oil can cause severe burns.

Do not remove components from the products

Only Beckhoff Automation GmbH & Co. KG is permitted to remove
components.
Contact Beckhoff Service if you have any questions.

Removal of the motor from the machine

• Remove cables and electrical connections

• Cool and drain liquids, then remove

• Remove supply lines and water hoses

• Loosen and remove the fixing screws of the motor

• Transport the motor to the work area or store it

Summary of Contents for AM8000 Series




























































































































Search results

Summary of Contents for AM8000 Series

Reviews:

Related manuals for AM8000 Series

Brands by name

Popular brands

Beckhoff AM8000 Series, Operation Instructions Manual

Search results

Summary of Contents for AM8000 Series

Reviews:

Related manuals for AM8000 Series

Brands by name

Popular brands