Beckhoff AM8000 Series Operation Instructions Manual Download Page 113

Page: 113 / 123

Fault correction

Version: 4.3

───

113

AM8000 and AM8500

Number

Cause

Solution

Servo drive not enabled

Set ENABLE signal and enable servo drive

Motor overload

Check the load and if necessary reduce it, then
restart and enable the servo drive. Set EN-
ABLE signal

Mechanical blockage of the motor

Check mechanics and release blockage

Holding brake [+] not released

Check the control configuration of the holding
brakes [+] and reconfigure if necessary

Phase interruption in the power supply or reversed
motor phases

Check servo drive and supply cables and re-
place any defective cables

Phase interruption after power supply; switching on Check servo drive and supply cables and re-

place any defective cables

Power cable or feedback cable with defective
shield

Check earth connection and shielding

Short-circuit in the voltage supply cable for the
holding brake [+]

Replace defective cable, measure and check
cable after replacement

Output voltage of the servo drive too low

Check the settings in the configuration and
read out the electronic type plate of the motor
again

Defective holding brake [+]

Replace motor, then measure and check

Short circuit or earth leakage in the motor cable

Replace defective motor cable, then measure
and check

Power connector not fitted correctly

Check the connectors on the power connector
and on the motor

Interruption in the feedback or motor cable

Check cables for broken wire or crushing. Re-
place defective cables, then measure and
check.

Summary of Contents for AM8000 Series




























































































































Search results

Summary of Contents for AM8000 Series

Reviews:

Related manuals for AM8000 Series

Brands by name

Popular brands

Beckhoff AM8000 Series, Operation Instructions Manual

Search results

Summary of Contents for AM8000 Series

Reviews:

Related manuals for AM8000 Series

Brands by name

Popular brands