manualshive.com logo in svg

Beastx Aircraft, Instruction Manual, Page: 66 / 88

Share
Download
Beastx Aircraft Instruction Manual Download Page 66

66 

When using the predefined control behaviors we do not recommend to additionally adjust con-

trol curves (expo/Dual rates) in your transmitter as this will mix indefinable the preset curves of the 

Microbeast with the curves of the transmitter .

 But if you only make little changes (e.g. slightly 

increasing the servo throw to increase rotation rate) this should be no problem.

Additionally when using the setting “transmitter” by increasing the tail stick throw, in HeadingLock 

mode you get to an additional feature where the tail rotation rate is not limited by the gyro anymore. 

With this feature, extremely high tail rotation rates are possible. The state of the Status-LED shows if this 

high rate mode is reached. If the LED starts to flash at full tail stick input, you are on the controlled 

rotation rate limit. If you increase the tail stick servo travel further, the Status-LED will end up turning 

off when at full stick input. From this point on the rotation rate is no longer limited by the maximum 

gyro sensor capability, and you get into a free spinning area that can not be controlled by the gyro 

anymore. By further increasing the stick input (dual rates, or servo end points), the maximum rotation 

rate will increase even further, as far as the mechanics of the helicopter will allow it!

The option “user defined” allows you to define your own setting with the PC software.

Push the button to save the configuration and to proceed to parameter menu point 

C

 .

This feature should only be used briefly for special Show-maneuvers, for instance by temporarily 

switching the dual rate to higher stick throw . Note there is no tail gyro control in this 

unregulated range and it is very difficult to properly control the tail in this state!

Therefore, make sure that in normal flight operation the Status-LeD at full rudder stick does 

not turn off . If it does, please reduce the servo throw or dual rate for the tail channel in your 

remote control .

Summary of Contents for Aircraft

























































































Reviews:

No comments