manualshive.com logo in svg

Beastx Aircraft, Instruction Manual, Page: 40 / 88

Share
Download
Beastx Aircraft Instruction Manual Download Page 40

40 

There is a relationship between the setting of the tail servo center position pulse length and the tail servo 
frequency (menu point 

D

). If a pulse length is selected that does not allow a certain frequency, this fre-

quency is automatically reduced. The center position pulse-setting always has priority, since a servo can 
run without problems at a too low frequency but can not be operated with an incorrect center position 
pulse. 

On 

WWW .beASTX .COM

 you can find a list of parameters for the most common servos.

The color of the Status-LED 

shows the currently selected 

servo center position pulse 

length: 

C

 Tail servo center position  pulse length

At setup menu point 

C

 you can select the pulse length for the tail servo‘s center position. Almost all 

commercially available servos work with 1520 μs. But there are a few special tail servos on the market 

which use a different center position pulse length.

To select the desired servo center position pulse repeatedly move the tail stick in one direction until the 

Status-LED glows in the correct color.

The option “user defined” allows you to define your own setting with the PC software.

Push the button to save the configuration and to proceed to setup menu point

 

D

 .

Status-LeD

Tail servo center position  pulse length

purple

960 μs

red

760 μs

blue

1520 μs *

off

User defined

*

 Factory Setting

Summary of Contents for Aircraft

























































































Reviews:

No comments