manualshive.com logo in svg

Beastx Aircraft, Instruction Manual, Page: 64 / 88

Share
Download
Beastx Aircraft Instruction Manual Download Page 64

64 

A

 Swashplate cyclic center adjustment

The first menu point in the parameters menu gives you the possibility to easily adjust your servo 

centers on the flying field as for instance your helicopter is wobbling during  pirouettes or when it 

doesn’t climb out straight on quick pitch inputs.

  

Never use the trim functions of your remote control!

         The MICROBEAST will see trim as a control command and not as servo trim.

Contrary to centering every single servo in the setup menu point 

G

, here you are able to directly adjust 

aileron and elevator without taking care about the single servos. However, the collective pitch cannot 

be adjusted here.

Similar to the digital trim function of most transmitters here at parameter menu point 

A 

you can 

adjust the swashplate “one click“ by shortly moving the aileron or elevator stick in the desired direction. 

If you want to trim the swashplate any further repeat tapping the stick several times or simply hold the 

control stick pushed for a longer time to automatically perform several trim steps.

During the sub trim procedure you can delete the just performed trimming by moving the tail stick in 

any direction. Additionally the color of the Status-LED gives you an approximate indication of how 

much you did trim.

But remember that this function as opposed to the digital trim of the transmitter is not

a separate trim function. Here you directly adjust the servo centers as well as you would set servo 

centers in the setup menu point 

G

. If the new position is saved once then this corresponds well to the 

new servo center position in the setup menu point 

G

. A subsequent reset to the previous state is not 

possible anymore!

Push the button to save the configuration and to proceed to parameter menu point 

B

 .

Summary of Contents for Aircraft

























































































Reviews:

No comments